All reproduced material copyright the original owners. All original material copyright 2005-2007 Michael J. Edelman unless otherwise noted. No material may be reproduced in any form without express written permission of the copyright holder(s).
If you're not viewing this page in a frame, with a menu along the left side of the page, click here.
|
John Zohlen, of Edgewater MD, has provided us with these specs from his 1989 Peep Hen, built by Mirage Fiberglass of Palatka FL.
LINE MATERIAL DIA. LENGTH ENDS NOTES
1. sail head lacing braided dacron 5/16” whipped/whipped
2. sail luff lacing braided dacron 5/16” whipped/whipped
3. parrel line 3-strand filament dacron 3/16” 1’-6” stopper knot/stopper knot
4. gaff jaws bridle 3-strand filament dacron 3/16” 1’-6” stopper knot/stopper knot
5. throat halyard 3-strand filament dacron 1/4” 50’-0” bowline/stopper knot
6. peak halyard 3-strand filament dacron 3/8” 73’-0” whipped/bowline
7. jiffy reef tack pendant braided dacron 5/16” stopper knot/bowline
8. jiffy reef leech pendant 3-strand filament dacron 3/16” 18’-0” tent hitch/bowline
9. lazy jack (upper) 3-strand filament dacron 3/16” 23’-0” bowline/bowline
10. lazy jack (lower) 3-strand filament dacron 3/16” 16’-0” cleated/bowline
11. tack hold down 3-strand filament dacron 3/16” 1’-10” square knot
12. tack out haul 3-strand filament dacron 3/16” 3’-9” bowline/cleated
13. main sheet braided dacron 3/8” 26’-0” stopper knot/bowline replace with 35’
14. mooring lines (2) three strand nylon 3/8” 20’ 0” whipped/whipped
15. mast line tender braided dacron 1/8” 14’-0” bowline/cleated
16. anchor rode 3-strand nylon 3/8” bowline/whipped
Note: Knot ends are identified in the following order:
1. starboard to port
2. forward to aft
3. top to bottom
For HIN: SJR0005PB989 Manufacturer: Mirage Fiberglass of Palatka FL |
|
||||||||
BLOCKS |
TYPE |
MANUFACTURER |
MODEL. |
LINE (INCHES) |
MWL (LBS) |
BL (LBS) |
SHEAVE DIAMETER |
||
1 |
Throat halyard (upper) |
Single block, becket, loop top |
Sail Speed |
Note 1 |
5/16 |
|
|
1 1/8” |
|
2 |
Throat halyard (lower) |
Single block, loop top |
Sail Speed |
Note 2 |
5/16 |
|
|
1 1/8 “. |
|
3 |
Peak halyard (upper) |
Single block, loop top |
Sail speed |
Note 2 |
5/16 |
|
|
1 1/8” |
|
4 |
Peak halyard (mid-gaff) |
Single block, loop top |
Sail Speed |
Note 2 |
5/16 |
|
|
1/8” |
|
5 |
Peak halyard (lower) |
Single block, swivel head post, shackle top |
Ronstan Series 28 |
RF 894 |
5/16 |
352 |
1630 |
1 1/8” |
|
6 |
Topping lift |
Single block, swivel head post, shackle top |
Ronstan |
RF 20100 |
1/4 |
550 |
1210 |
20mm |
|
7 |
Turning, mast (throat and peak halyard) |
Double block, swivel head post, shackle top |
Harken |
127 |
3/8 |
600 |
|
1 ½” |
|
8 |
Main sheet (boom) |
Single block, universal head |
Ronstan Series 45 |
RF 1250 |
3/8 |
902 |
1804 |
1 ¾” |
|
Main sheet (rudder head) |
Single block, becket , universal head |
Ronstan Series 45 |
RF 1251 |
3/8 |
902 |
1804 |
1 ¾” |
|
|
|
|
|
|
|
|
|
|
Notes |
|
1. Similar to Ronstan Series 28. model RF893. The Series 28 have a maximum working load of 352 lbs. and breaking load of 1980 lbs. 2. Similar to Ronstan Series 28, model RF892. |
|
Bolt, mast (upper) |
3/8” x 5 ½” |
S/S bolt |
Flat washers (2), lock nut (bolt had and nut 9/16”) |
|
2 |
Pin, mast (upper) |
3/8” x 5 ½” |
S/S pin |
Retaining rings (2) |
3 |
Bolt, mast (lower) |
3/8” x 5 ½” |
S/S bolt |
Flat washers (2), lock nut (bolt had and nut 9/16”) |
4 |
Pin, mast (lower) |
3/8” x 5 ½” |
S/S pin |
Retaining rings (2) |
5 |
Bolt, rudder pivot |
¼” x 2” |
S/S oval, Phillips head |
Flat washer with lock nut (7/16”) |
6 |
Bolt, rudder stock (2) |
¼” x 1 ¾” |
S/S oval, Phillips head |
Flat washer with lock nut (7/16”) |
7 |
Bolt, pintle and gudgeon (4) |
¼” x 2 ½” |
S/S oval, Phillips head |
Flat washer with lock nut (7/16”) |
8 |
Bolt, boarding ladder (9) |
¼” x 2 ½” |
S/S oval, Phillips head |
Flat washer with lock nut (7/16”) |
9 |
Cleat, bow |
6” |
plastic |
Manufacturer unknown |
10 |
Cleat, quarter (2 |
4” |
|
Manufacturer unknown |
11 |
Eye strap (8) |
1 7/8” long 5/16’ ID eye |
Perko # 1242-DP-CHR |
#8 mounting screws |
12 |
Ventilator, cowl |
8” h x 3” dia. 3 ¾” cutout |
Nicro No. 124208 |
|
13 |
Deck plate, screw in |
6” diameter |
Beckson DP60-W-C |
West Marine Catalog # 103630 |
14 |
Port, opening |
4” x 11” |
|
Manufacturer unknown |